Garage Door Openers Discussion Board

AssureLink Gateway - not connecting to internet

Handynothandsome — Sat, 21 Jan 2012 02:44:47 GMT

I'm trying to install my new AssureLink Gateway, and it is not connecting to internet:
The green link light flashes briefly on start-up, but does not stay on, indicating it has not made a connection. The blue light is on.

I've logged into my ethernet router and confirmed it sees the gateway and has assigned it an IP address. When I am on the AssureLink website I get the following error message: "The gateway is not responding. Please check the power and Ethernet cable connections."

I've tried changing ethernet cables, power-cycling the gateway, and pressing the 'soft reset' button. None have worked.

Any suggestions?

Wiring the Sears 139.53990DDS garagedoor opener and GTO RB709 universal receiver.

w4qed — Thu, 01 Dec 2011 08:31:30 GMT

OK let me try this. Does anyone have the description of RED-WHT-WHT-GRAY terminals on the Sears 139.53990DDS unit?

IE: +volts-gnd-pulse...

Wiring the Sears 139.53990DDS garagedoor opener and GTO RB709 universal receiver.

w4qed — Wed, 23 Nov 2011 18:59:11 GMT

Looking for either the GTO RB-709 universal rerceiver wiring to the Sears garage door opener or a description of the RED-WHT-WHT-GRAY terminals on the Sears 139.53990DDS unit. Only description I've seen for the Sears unit Is Red-Terminal 1, WHT-Terminal 2, GRAY-Terminal 3 or something like that.

I have two Garage door openers and a Sliding gate and I want to be able to use only 1 remote for all three. Pashaps Sears has a universal 315MHz receiver?

GOD assembly

shady08798 — Wed, 23 Nov 2011 00:04:40 GMT

i recently purchased the craftsman assurelink 3/4hp belt drive unit and went to assemble it and got to the point where i attach the belt and it comes up 2-3 inches short of being able to put it in the whole to attach the tenson screw any suggestions ive tried for about half an hour and no luck

Motion sensor does not turn light on

anoscrn — Fri, 11 Nov 2011 12:30:44 GMT

That's one of those ideas where you smack your head for not thinking of it yourself. Great suggestion -- the new opener is a 'better' model (with the battery backup) but I'll bet the signals coming out of the wall control are the same. Regardless, it's easy to try and can't hurt... Thanks!

Motion sensor does not turn light on

BigMike4511 — Fri, 11 Nov 2011 12:08:37 GMT

If the controllers are the same, an easy diagnostic test is to take the known good one and switch it with the one in question. You will then know if the problem is in the controler or something else is wrong with the opener.

Motion sensor does not turn light on

anoscrn — Fri, 11 Nov 2011 04:43:19 GMT

Thanks for the quick response. I was hopeful because I hadn't tried that before -- light even went out then back on after 10 seconds just as you mentioned....but once it went off after the auto 4.5 mins it still doesn't come on automatically. I'm thinking I might have a bad controller on that unit. Recently bought another craftsman gdo for a different door and the motion detector worked like a charm right from the start. That's what prompted me to post my questions -- thought it would be nice to have both working. But thanks for the suggestion.

Motion sensor does not turn light on

Billfish — Fri, 11 Nov 2011 04:11:35 GMT

The manual says to activate the motion detector feature,start with the opener lights "on",press and hold the "light" button for ten seconds,the lights will go out,then on again.Never seen it myself,just quoting the manual.

Motion sensor does not turn light on

anoscrn — Thu, 10 Nov 2011 23:56:00 GMT

I have a Craftsman model 139.53915D GDO and the light does not come on when someone walks in front of the motion sensor on the Control Console (never worked). Any ideas how to fix it?

Remote will open garage door but will not close it

qraine80 — Fri, 21 Jan 2011 00:32:36 GMT

Thanks....sounds like a maintenance call!

Remote will open garage door but will not close it

wstarc5 — Thu, 20 Jan 2011 23:33:44 GMT

The safety sensor are misaligned or have failed.

Remote will open garage door but will not close it

Billfish — Thu, 20 Jan 2011 23:28:08 GMT

This normally indicates a problem with the photo cell sensors.The reasoning is that the sensors are taken out of the circuit in "open" mode.

Remote will open garage door but will not close it

qraine80 — Thu, 20 Jan 2011 23:19:51 GMT

Help! My remote will open the garage door but will not close it. Also, you must hold the wall unit down until the door COMPLETELY closes. Appreiate any suggestions.

a lot of slack appears in the belt when my belt drive opener opens my door.

chili55 — Thu, 20 Jan 2011 13:35:18 GMT

made a call. weak springs. thanks for all the help!

a lot of slack appears in the belt when my belt drive opener opens my door.

chili55 — Wed, 19 Jan 2011 17:11:38 GMT

i am a little unsure so i'll probably give someone else a call. thanks for the help.

a lot of slack appears in the belt when my belt drive opener opens my door.

BigMike4511 — Wed, 19 Jan 2011 17:07:58 GMT

You may not need to replace the springs; you may be able to adjust the tension. This is done either by shortening the cable length, or depending on how the springs are attached you may be able to adjust them by tightening a nut on the mounting.

There is some serious power in the springs, and if you do not know what you are doing, you can cause yourself serious injury. If you are unsure, this is one time when DIY is not a good idea.

a lot of slack appears in the belt when my belt drive opener opens my door.

chili55 — Wed, 19 Jan 2011 16:50:55 GMT

sounds like that is where i'm at. How tough is it to replace springs?

a lot of slack appears in the belt when my belt drive opener opens my door.

Don2000 — Wed, 19 Jan 2011 16:45:16 GMT

Unless the spring is broken the only way to tell is the weight of the door. If the door seems a little heavy to you it is heavy for the opener.

a lot of slack appears in the belt when my belt drive opener opens my door.

chili55 — Wed, 19 Jan 2011 16:22:27 GMT

how do you tell a bad spring from a good spring? would it be stretched out? the door opens ok but does seem a little heavy opening by hand.

a lot of slack appears in the belt when my belt drive opener opens my door.

Don2000 — Wed, 19 Jan 2011 16:12:23 GMT

I would really be concerned about the weight of the door. It sounds as if you may have bad springs or even one that is broken. You can release the door from the opener and try operating it by hand. Should give you an idea.